ماژول مبدل PWM به ولتاژ 10-0 ولت

[COM-05-069]
امتیاز:
100 % of 100
2 نفر از خریداران، این کالا را پیشنهاد کرده اند
گارانتی اصالت و سلامت فیزیکی کالا جزئیات
30 هزار تومان تخفیف اولین خرید با کد HELLO (حداقل خرید 300 هزار تومان)
موجودی: موجود نیست
کد انبار
COM-05-069
محصولات مرتبط

ماژول مبدل PWM به ولتاژ 10-0 ولت LC-LM358-PWM2V یک ماژول کاربردی است که سیگنال‌های دیجیتال PWM را به سیگنال‌های آنالوگ 0 تا 10 ولت تبدیل می‌کند. این ماژول برای استفاده در کنترل‌های صنعتی و اتوماسیون بسیار مناسب است و به راحتی می‌تواند به سیستم‌های PLC یا سایر بردهای کنترل صنعتی متصل شود.

مشخصات فنی ماژول مبدل PWM به ولتاژ 10-0 ولت

  • ولتاژ کاری: 12V-30V DC (> 100mA)
  • فرکانس سیگنال PWM دریافتی: 1KHz-3KHz
  • محدوده ورودی سطح سیگنال PWM:

    • پیک 4.5V تا 10V (با قرار دادن جامپر در 5V)
    • پیک 12V تا 24V (با قرار دادن جامپر در 24V)
  • محدوده تبدیل: 0%-100% PWM به 0-10V ولتاژ
  • خطای مجاز: 5%
  • اندازه: کوچک و قابل حمل

ویژگی‌های کلیدی ماژول مبدل PWM به ولتاژ 10-0 ولت

  • تکنولوژی embedded: این ماژول از تکنولوژی تک تراشه استفاده می‌کند که عملکرد آن را بهینه می‌کند.
  • تنظیم آسان: می‌توان به راحتی ولتاژ خروجی را با تنظیم نسبت وظیفه PWM تنظیم کرد.
  • کالیبراسیون ساده: پس از روشن کردن، با ورودی سیگنال نسبت وظیفه 50% و اندازه‌گیری با مولتی‌متر، ولتاژ خروجی باید 5V تنظیم شود. در صورت تغییر فرکانس، ممکن است نیاز به کالیبراسیون مجدد باشد.
  • کاربردهای متنوع: به عنوان رابط سیگنال برای سوئیچینگ در PLC یا سایر بردهای کنترل صنعتی استفاده می‌شود.

پایه های ماژول مبدل PWM به ولتاژ 10-0 ولت

  • VCC: ولتاژ کاری 12-30 ولت
  • GND: زمین
  • PWM: مثبت سیگنال PWM ورودی
  • GND: زمین ولتاژ ورودی
  • VOUT: ولتاژ خروجی: 0-10 ولت
  • GND: زمین خروجی

نحوه استفاده از ماژول مبدل PWM به ولتاژ 10-0 ولت

پس از روشن کردن ماژول، بدون سیگنال ورودی، خروجی 0 ولت است. برای کالیبراسیون، سیگنال نسبت وظیفه 50% را به ورودی PWM متصل کنید و با تنظیم پتانسیومتر، ولتاژ خروجی را به 5V تنظیم نمایید. این ماژول به سادگی در پروژه‌های مختلف صنعتی و اتوماسیون قابل استفاده است.

 

Instruction

After power on, without input signal, the output is 0V, so only input can output.

The first time when the power is on, it is best to do a calibration debugging:Input a 50% duty ratio signal to PWM/GND and adjust the relative amplitude short cap. The frequency is 1KHZ-3KHZ, Measured VOUT and GND with a multimeter and it will display 5V. Adjust potentiometer to make sure display 5.00V on multimeter. This will calibrate your pulse signal to this module.

When the frequency changes, the correspondences may be offset and need to be re calibrated.

The output voltage can be adjusted by adjusting the duty ratio.

The accuracy can be controlled by adjusting the potentiometer.

he PWM transfer voltage module LC-LM358-PWM2V converts the PWM digital signals into 0 to 10V analog signals.

It can be used as signal interface switching for PLC or other industrial control boards. The output voltage is regulated by adjusting the duty ratio of the PWM. The modules are small in size and easy to use in different places.

Specification

Using single chip embedded technology;

Peak 4.5v to 10V level, jumper inserted at 5V. This level of signal mainly for conventional industrial control card (such as MACH3 board Card) 5V CPU interface;

Easy to operate, can be fine-tuned by potentiometer;

Select the PWM signal input level range through short cap;

Module is small, easy to carry and use;

Module operating voltage: DC12V-30V (power requirements: greater than 100mA);

PWM signal reception frequency range: 1KHz-3KHz;

Peak 12 to 24V level, jumper inserted in the 24V. This level of signal is mainly aimed at the conventional PLC interface;

Conversion range: 0% -100% PWM to 0-10v voltage;

Allowable error: 5%;

MCU embedded technology

Easy to operate, fine tuned by potentiometer

Select the PWM signal input level range through short-circuit

The module is smaller, easy to carry and use

Parameters

Work Voltage:DC 12V-30V; (> 100MA)

PWM Receiver Frequency:1KHZ-3KHZ

PWM signal input level range:

The peak of 4.5V to 10V level. The short cap install in ‘5V’. This level is used for normal controller or 5V MCU

The peak of 12V to 24V level, so inserted in 24V. The short cap install in ‘24V’. This level is used for normal PLC controller

Conversion range:0%-100% PWM to 0-10V

Allowable error:5%

Hardware Interface

VCC: working power 12-30V

GND: ground

PWM: input PWM signal positive

GND: input voltage ground

VOUT: Output voltage: 0-10V

GND: output ground

خریداران این محصول، محصولات زیر را هم خریده‌اند
mgctlbxN$MZP mgctlbxV$5.3.7 mgctlbxL$T mgctlbxP$magento 2